What exactly is concentrated solar-thermal power (CSP) and how does it work? Mirrors are used in CSP technologies to reflect and concentrate sunlight onto a receiver. In the receiver, the energy from concentrated sunlight heats a high-temperature fluid.

This heat, also known as thermal energy, can be used to generate electricity by spinning a turbine or powering an engine. Water desalination, increased oil recovery, food processing, chemical production, and mineral processing are just a few of the industrial applications.

Utility-scale projects often employ concentrated solar-thermal power systems. Utility-scale CSP plants can be set up in a variety of methods. Mirrors are arranged around a central tower that serves as the receiver in power tower systems. Linear systems use rows of mirrors to focus sunlight onto parallel tube receivers that are positioned above them.

Smaller CSP systems can be installed just where electricity is needed. Single dish/engine systems, for example, can produce 5 to 25 kilowatts per dish and can be employed in distributed applications.

CSP (concentrated solar power) is a method of generating electricity in which sunlight is reflected, concentrated, and focused into a single point using mirrors. The concentrated light is transformed into heat, which is then used to produce steam. The steam is then utilized to power a turbine, which produces electricity.

Solar electricity is stored using CSP technology and can be used on overcast days and in the hours after sunset or before sunrise. CSP is still a relatively new method of generating electricity, and it is most typically employed in utility-scale projects as of this writing.

The ability of concentrated solar power (CSP) to store thermal energy has made the renewable energy source particularly attractive in the United States Sun Belt region. Georgia, South Carolina, Alabama, Mississippi, Louisiana, New Mexico, Arizona, Nevada, and Texas are all part of the Sun Belt region, which stretches from California to Florida and includes Georgia, South Carolina, Alabama, Mississippi, Louisiana, New Mexico, Arizona, Nevada, and Texas.

For nearly 15 years, CSP facilities have been reliably functioning in the United States. The Crescent Dunes power plant, for example, was built with US Department of Energy (DoE) money in the 1990s in the Mojave Desert, which stretches through southeast California and southern Nevada. Molten salt is used as a heat transfer fluid and storage medium in the power plant, resulting in increased efficiency and cost-effectiveness.

The successful construction of a concentrated solar power system depends on a number of criteria. The following are the most important requirements:

To focus sunlight onto the receiver situated at the focal point of the dish, parabolic dish systems use u-shaped or parabolic mirrored dishes about 10 times the size of a domestic satellite dish. This receiver is built inside a high-efficiency external combustion engine that uses tubes that carry hydrogen or helium gas and open into the four piston cylinders.

The focused sunlight heats the gas in the tubes to severe temperatures, causing the hot gas to expand within the cylinders as it passes through the receiver. This expanding gas drives pistons, which spin a crankshaft, which drives the generator, which generates energy.

In a parabolic dish system, the receiver, engine, and generator are all merged into a single unit that is situated at the mirrored dish’s focal point. The dish system, similar to a tracking array, tracks the sun’s motion across the sky in order to catch the maximum amount of solar energy.

U-shaped mirrors with oil-filled pipes running along the focus point are used in parabolic trough systems. The mirrors face the sun and concentrate the light onto the pipes, which heats the oil inside to temperatures of up to 750 degrees Fahrenheit. The heated oil is then used to boil water and generate steam, which powers turbines and generators.

Long parallel rows of flat mirrors are used in compact linear Fresnel reflector systems, which are less expensive than curved reflectors in the parabolic trough system. The small linear Fresnel system’s flat mirrors concentrate sun light onto raised receivers with a cluster of tubes filled with flowing water. The concentrated sunlight is utilized to boil water, resulting in steam that can be used to generate electricity.

Many enormous, flat mirrors track the sun and focus the solar energy onto a receiver in power tower systems, also known as central receivers. The receiver in this system sits atop a tall tower and catches sunlight, which is then used to heat fluids like molten salt, which may reach temperatures of up to 1,050F. The heated fluid can either be used right away to generate steam and energy, or it can be stored and conserved for later use.

One of the key advantages of solar power systems is the decrease of carbon emissions. Other advantages include:

The concept of concentrated solar power was first discovered by Archimedes in 214-212 BC, according to Greek mythology. He devised a defense strategy that involved men utilizing bronze shields to focus sunlight onto invading Roman ships, causing the ships to catch fire. August Mouchout used a parabolic trough system to heat water and make steam in order to run the first solar steam engine in 1866, which was the first documented usage of CSP.

Frank Schuman, a Philadelphia inventor, installed a parabolic trough system in a tiny farming village in Meadi, Egypt, in 1912.

The troughs were used to generate steam, which was then utilized to power massive water pumps that could supply 6,000 gallons of water per minute to broad desert areas.

Professor Giovani Francia established the first operational CSP plant in Sant’Ilario, Italy, in 1968. A power tower system was used at the plant, which was encircled by a field of additional solar energy collectors.

Solar One was founded in 1982 by a group of solar industry organizations and the US Department of Energy. Solar One was a 10 MW power tower system demonstration project that proved the system’s viability and functioning.

In Kramer Junction, California, the world’s largest solar power complex was inaugurated in 1986. The method focused solar light onto a system of pipes and heated the transfer fluid inside using rows of mirrors. The steam generated fueled a turbine, which generated electricity.

Solar Two, a project that was supposed to be an upgrade on the Solar One power tower project, was developed between 1996 and 1999 by the US DOE and a group of solar industry companies.

Concentrated solar power continues to develop in terms of use and accessibility because to advancements and inventions. CSP systems are constantly improved and used, allowing them to run at higher efficiency and power a wide range of utility-scale projects.

The utilization of space-based solar power has been studied since the mid-twentieth century (SBSP). SBSP refers to the idea of capturing solar energy in space and then transferring it to Earth or other planets for use as electricity. SBSP has the potential to solve the global greenhouse effect with low environmental impact.

Using concentrated solar electricity as part of an SBSP system is one option. These SBSP systems use mirrors to focus solar radiation, which heats a liquid and drives a turbine, which generates electricity.

The high expense of procuring and shipping all of the necessary materials is one impediment to extensive development and implementation of space-based solar power systems. SBSP has the potential to offer consistent, clean, and reliable power at lower rates, but it will take many years of development, testing, investment, and successful installations before the system can begin to recoup its original expenditures.

Mirrors are used in Concentrating Solar Power (CSP) technologies to focus (focus) the sun’s light energy and convert it to heat, which is then used to drive a turbine that creates electricity.

CSP technology makes advantage of concentrated sunlight. CSP plants generate electricity by concentrating (focusing) the sun’s energy and converting it to high-temperature heat using mirrors. The heat is then transferred to a traditional generator. The plants are divided into two sections: one that absorbs solar energy and converts it to heat, and the other that transforms heat energy to electricity. The Department of Energy’s Solar Energy Technologies Web site has a short video that explains how concentrating solar power works (using a parabolic trough system as an example).

CSP facilities have been operating reliably in the United States for more than 15 years. When used to generate energy at commercial scale, all CSP technical approaches necessitate enormous areas for solar radiation gathering.

Trough systems, power tower systems, and dish/engine systems are three different technological techniques used in CSP.

CSP is utilized to assist power an electricity system in utility-scale applications. They can be used in conjunction with energy storage technologies to store thermal energy for use when the sun’s irradiance is low, such as at night or on a cloudy day.

CSP is utilized to assist power an electricity system in utility-scale applications. They can be used in conjunction with energy storage technologies to store thermal energy for use when the sun’s irradiance is low, such as at night or on a cloudy day.

In any case, both CSP and PV contribute to the growth of the solar industry. They are the ones who made solar power conceivable, and they are the ones who will ensure that solar power is here to stay.

The advancement of the technology linked with solar power energy has resulted in a surge in its appeal. After all, once people understood the sun could be utilized to generate power, they would naturally look for ways to do it. So far, there are just two technologies that are currently employed to create solar energy. Concentrated Solar Power (CSP) and Photovoltaic (PV) are two of them (PV).

Due to the utilization of a traditional, rotating turbine that adds inertia to the grid, CSP also provides crucial grid stabilizing qualities. Utilities and independent system operators (ISOs) are responsible for satisfying customer energy requests, and utilities must guarantee that the grid remains stable when energy demands fluctuate rapidly.

Frequency and voltage regulation, short-circuit power, and spinning reserves, which are energy that is already online and synchronized to the grid’s frequency, are all managed by utilities and ISOs to meet these needs. This makes it easy to keep the system running at a high frequency and immediately dispatch additional energy. CSP can provide spinning reserves for immediate demands and non-spinning reserves for near-term needs, offering grid operators more flexibility and control when it comes to assuring grid resilience.

One of the most significant advantages of CSP is its energy source’s dependability and predictable pricing. Unlike traditional fuels, there is no need to harvest, ship, burn, or store waste because sunlight is unlimited and endless. Because the “fuel” is free, the costs of a plant’s operation and maintenance are predictable over time. Furthermore, the first year accounts for more than 60% of the cost of operating a CSP power plant, allowing investors to gain a better long-term understanding of costs and returns.

The fact that CSP is renewable is perhaps the most obvious advantage. Its supply will never run out and may be used indefinitely, making it a long-term energy source. It also cuts down on carbon emissions. Unlike fossil fuels, which generate carbon dioxide when burned, CSP makes use of the earth’s natural resources, making it more environmentally friendly. It has the potential to enhance air quality while also slowing the rate of climate change.

In comparison to solar photovoltaics (PV) and wind power, which provide intermittent supply, CSP provides a relatively constant source of electricity. The power generated by CSP facilities is predictable and stable because solar energy is stored in the form of molten salts.

Existing steam-based power facilities can readily be converted to CSP. CSP systems can be employed in vehicles that run on fossil fuels. Because operations and maintenance are simpler, CSP plants have lower operating costs than nuclear and hydrocarbon-based plants.

Concentrated solar power can be used with other energy sources to create a more reliable energy grid. CSP can assist satisfy future electricity demand if it is included in the energy mix. It can also help with oil recovery by concentrating heavy oil so it’s easier to pump with the steam it produces.

It also has the potential to be used as a portable energy source. For example, the renewable energy consultancy Ecofys issued a research to evaluate the potential of CSP as a technology for producing cost-effective hydrogen that may be used to power transportation.

The term “solar thermal” has been applied to two distinct types of systems. One is where solar panels collect heat for use as home or process hot water, space heating, or, in some circumstances, air conditioning. Solar heating and cooling (SHC), the most fundamental kind of solar energy consumption, was discussed in a previous post.

The other form of solar thermal system uses concentrating solar collectors to focus sunlight and increase its intensity to generate extremely high temperatures that can be converted to steam and used to power a traditional thermal power plant or heat engine. This is known as concentrating solar power (CSP), and it’s what we’ll talk about today.

There are three major types of CSP systems, according to the National Renewable Energy Laboratory (NREL): linear concentrator, dish/engine, and power tower systems.

Curved panels reflect and focus the sun’s rays onto a tube that runs the length of the panel in linear concentrators. A fluid is contained in the tube, which heats up and produces steam, which is used to power a turbine. The parabolic trough type, in which the tube runs down the focal line, and the linear fresnel type, in which Fresnel lenses collimate the reflected beam so that one receiver tube can be positioned over numerous mirrors, are the two primary types. This type offers more flexibility in tracking the sun while also being less expensive.

Dish engine systems range in size from 3 to 25 kW, which is smaller than linear concentrators. They are made up of a circular parabolic disk mirror that tracks the sun’s position and focuses its rays onto a power conversion unit that is situated along an axis extending outward from the disk’s center at the required focusing distance, which is determined by the disk’s curvature. A thermal receiver and a heat engine make up the power conversion unit. The heat reflected from the mirror is absorbed by the thermal receivers and transferred to the heat engine. The Stirling engine is the most widely utilized heat engine. Stirling engines, unlike internal combustion engines, are heated from the outside and do not require the internal explosions that are typical of today’s automobile engines. They are significantly cleaner and potentially cheaper to operate than fossil fuel fueled engines since they can be heated by a variety of energy sources, including concentrated sun. The fact that they are slow to respond to changes is their major flaw, rendering them unsuitable for vehicle use (except perhaps in a hybrid system where they might be used to recharge a battery).

Finally, there are the power towers, which are possibly the most spectacular and scalable systems. Power towers, also known as point-focus central receiver systems, are similar to dish/engine systems with the exception that there is a single central engine surrounded by several dishes that all focus on it. The heated receiver generates steam, which is utilized to power a traditional turbine generator. In the 1990s, two 10-megawatt plants were successfully tested in the United States. Spain has also installed multiple 20MW units, the most current of which uses molten salt for energy storage and transfer. eSolar launched a 5MW power tower installation with 24,000 mirrors in 2009. For power tower technology, the DOE is currently constructing a 200-megawatt molten-salt solar receiver panel. In the United States, BrightSource Energy’s 392MW Ivanpah facility on the California-Nevada border and SolarReserve’s 110MW Crescent Dunes facility northwest of Las Vegas are both expected to be completed next year.

There will be more in the future. Saudi Arabia recently announced intentions to invest $109 billion in solar power, with the goal of generating 41 gigawatts (GW), or about a third of the country’s estimated consumption by 2030. The specifics are unknown at this time, although it will very certainly entail power tower facilities.

Unlike solar PV and solar heating and cooling, which both take advantage of the fact that the sun shines everywhere and use an inherently distributed model, CSP follows the more traditional centralized utility model, in which power is transmitted over long distances from a capital-intensive central utility and sold to ratepayers.

CSP has the promise of a clean energy source that can be produced at scales equivalent to coal or nuclear under the right conditions, despite the fact that it is expensive and far from simple. Improved thermal energy storage technologies, while still vulnerable to intermittency, have been recommended as a key to CSP’s long-term viability.

Become a member of AEE

We are using cookies to give you the best experience on our website.

You can find out more about which cookies we are using or switch them off in settings .

Aplicación de la presente Política de Privacidad:

El presente documento regula la Política de Privacidad tanto del presente sitio web, así como de la totalidad de datos e información que pudiera manejar ASOCIACIÓN EMPRESARIAL EÓLICA (en lo sucesivo, "AEE") como Responsable del Tratamiento.

Por ello, para cumplir con el artículo 13 y 14 del Reglamento (UE) 2016/679 del Parlamento Europeo y del Consejo de 27 de abril de 2016 relativo a la protección de las personas físicas en lo que respecta al tratamiento de datos personales y a la libre circulación de estos datos (en lo sucesivo "RGPD" o "Reglamento General de Protección de Datos"), así como el artículo 11 de la Ley Orgánica 3/2018, de 5 de diciembre, de Protección de Datos Personales y garantía de los derechos digitales (en lo sucesivo "LOPDGDD") se ha establecido y desarrollado la presente Política de Privacidad.

Tus datos personales son manejados por, nosotros, AEE como Responsable del Tratamiento. Te detallamos nuestros datos sociales para que te puedas poner en contacto con nosotros cuando lo desees:

Razón social: ASOCIACIÓN EMPRESARIAL EÓLICA

Domicilio: C/ SOR ÁNGELA DE LA CRUZ, 2, PLANTA 14D – 28020 MADRID

Correo electrónico: datos@aeeolica.org

El presente apartado regula la totalidad de tratamientos llevados a cabo por AEE, en base a cada una de las finalidades, conforme a las bases legitimadoras que lo regulan, comprendido éstos en los que se enumeran a continuación:

Consentimiento del interesado (artículo 6.1. a) RGPD)

Usuarios página web: atender su solicitud a través del formulario de contacto.

Procesos de selección de personal: formar parte de los procesos de selección ofertados.

Ejecución contractual y medidas precontractuales (artículo 6.1.b) RGPD)

Gestión de alta como socio/asociado de AEE.

Mantenimiento y perfeccionamiento de la relación contractual pactada entre AEE y su empresa.

Gestión contable y administrativa del servicio entre AEE y su empresa.

Gestionar las comunicaciones electrónicas entre AEE y su empresa.

Atender cualquier solicitud de información que nos hagas llegar.

Hacerle llegar, en su caso, ofertas comerciales.

Mantenimiento y perfeccionamiento de la relación laboral pactada entre AEE y usted.

Gestión contable, fiscal y administrativa de la relación laboral.

Gestionar y realizar el pago de su nómina pactada contractualmente y exigidas por la legislación laboral.

Gestionar comunicaciones entre AEE y su usted.

Realizar el seguimiento de las acciones formativas de las que sea sujeto.

Gestión de bajas por enfermedad.

Interés legítimo del responsable del tratamiento (artículo 6.1.f) RGPD)

Actividades comerciales: envío de información comercial a usuarios sobre productos y servicios semejantes a los previamente contratados, en vinculación con el artículo 21.2 de la LSSICE.

Videovigilancia: gestión de la seguridad de instalaciones, bienes y personas a través de mecanismos de videovigilancia.

Asimismo, se le informa que todos los datos que AEE le solicite o pudiera solicitar marcados con un asterisco (*) serán obligatorios. En el caso de que los datos obligatorios no fueran facilitados AEE no podrá prestarle el servicio contratado o atender su petición o solicitud.

En cumplimiento del artículo 4.2.a de la LOPDGDD, se garantiza que los datos de carácter personal facilitados por usted hacia AEE se considerarán exactos. Sin embargo, AEE podría solicitarle la actualización de los mismos que sobre usted pudiera conservar.

Plazo de conservación de los datos:

En virtud del artículo 5.1.e) del RGPD, los plazos de conservación de los datos variarán en función del tratamiento realizado. Por ello, desde AEE le aconsejamos leer nuestra Política de conservación de datos para su consulta, la cual la podrá solicitar en datos@aeeolica.org

No obstante, pese a la existencia de estos plazos generales, le informamos que de forma periódica revisaremos nuestros sistemas para proceder a eliminar aquellos datos que no sean legalmente necesarios.

Derechos que le asisten a los interesados:

La normativa de protección de datos le reconoce los siguientes derechos:

Derecho a solicitar el acceso a sus datos personales.

Derecho a solicitar la rectificación de sus datos personales.

Derecho a solicitar la supresión de sus datos personales.

Derecho a solicitar la limitación del tratamiento.

Derecho a oponerse al tratamiento.

Derecho a no ser objeto de decisiones individuales automatizadas.

Derecho a retirar su consentimiento.

El ejercicio de tales derechos deberá ser comunicado a ASOCIACIÓN EMPRESARIAL EÓLICA, con domicilio en C/ SOR ÁNGELA DE LA CRUZ, 2, PLANTA 14D – 28020 MADRID, o la cuenta de correo electrónico datos@aeeolica.org. Adicionalmente, puede presentar una reclamación ante la Agencia Española de Protección de Datos (AEPD). Más información en el Apartado Autoridad de Control de la presente política de privacidad.

Destinatarios y transferencias internacionales de datos:

Sus datos personales podrían serán comunicados a Autoridades Públicas o gubernamentales, Fuerzas y Cuerpos de Seguridad del Estado, para dar cumplimiento a los requisitos legales y normativa aplicable en cada caso concreto.

A su vez, podrían ser comunicados a terceros proveedores o entidades para la prestación de algún servicio subcontratado por AEE. A este aspecto le informamos que se han firmado los correspondientes contratos de encargado del tratamiento exigidos por el artículo 28 y 29 del RGPD así como el artículo 28 de la LOPDGDD, y siempre éstos garantizando y siendo comprobado por AEE que cumplen y garantizan con medidas jurídicas, técnicas y organizativas suficientes. Le informamos que sus datos no serán comunicados a terceras personas. Ni se realizarán transferencias internacionales de datos.

Procedencia de los datos personales:

Los datos de carácter personal que trata AEE proceden de usted como titular de los mismos.

A las cuales, usted previamente le ha facilitado sus datos de carácter personal y ha autorizado la comunicación de los mismos a las diversas empresas que ofrecen sus servicios a través de estas empresas.

Desde AEE se han implantado medidas jurídicas, técnicas y organizativas suficientes para garantizar la protección de los datos personales. Por ello, revisamos periódicamente nuestros sistemas para evitar cualquier acceso no lícito, no autorizado, así como para evitar cualquier tipo de pérdida, destrucción accidental, divulgación ilegal o no autorizada, así como cualquier otro tipo de daño, tanto accidental como ilícito.

Desde AEE ponemos el máximo empeño para cumplir con la normativa de protección de datos dado que es el activo más valioso para nosotros. No obstante, le informamos que en caso de que usted entienda que sus derechos se han visto menoscabados, puede presentar una reclamación ante la Agencia Española de Protección de Datos (AEPD), sita en C/ JORGE JUAN, 6 - 28001 MADRID. Más información sobre la AEPD en su página web.

Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.

If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.

This website uses Google Analytics to collect anonymous information such as the number of visitors to the site, and the most popular pages.

Keeping this cookie enabled helps us to improve our website.

Please enable Strictly Necessary Cookies first so that we can save your preferences!

Aplicación de la presente Política de Cookies:

Desde la ASOCIACIÓN EMPRESARIAL EÓLICA (en adelante, "AEE") deseamos informarte de que nuestras páginas web utilizan cookies propias y terceros para medir y analizar la navegación de nuestros usuarios. Mediante el uso de nuestros sitios web aceptas nuestras cookies de conformidad con los términos de esta Política.

Una cookie es fichero que se descarga en su ordenador al acceder a determinadas páginas web. Cada cookie es única a su navegador web y contendrá cierta información anónima, como un identificador y el nombre de la página web, junto con algunas cifras y números. El usuario no proporciona directamente esta información, sino que se recaba automáticamente como medio de apoyo a su visita a la página web.

Las cookies permiten a una página web, entre otras cosas, almacenar y recuperar información sobre los hábitos de navegación de un usuario o de su equipo y, dependiendo de la información que contengan y de la forma en que utilice su equipo, pueden utilizarse para reconocer al usuario.

¿Qué tipos de cookies utiliza esta página web?

En el siguiente enlace podrá acceder al listado completo de las cookies que utiliza el presente sitio web. Las cookies podrán ser:

Propias: son las que se descargan en su navegador desde un dominio propio de AEE, siendo gestionadas por nosotros mismos.

De terceros: son las que se descargan en su navegador desde un dominio que no gestiona AEE, sino un tercero.

Estas cookies podrán tener diferentes finalidades. En función de estas finalidades, las cookies se pueden clasificar en:

Cookies necesarias: las cookies necesarias ayudan a hacer una página web utilizable activando funciones básicas como la navegación en la página y el acceso a áreas seguras de la página web. La página web no puede funcionar adecuadamente sin estas cookies.

Cookies estadísticas: las cookies estadísticas ayudan a los propietarios de páginas web a comprender cómo interactúan los visitantes con las páginas web reuniendo y proporcionando información de forma anónima.

Cookies funcionales: estas cookies permiten que el sitio web proporcione una mejor funcionalidad y personalización. Pueden ser establecidas por nuestra empresa o por proveedores externos cuyos servicios hemos agregado a nuestras páginas. Si no permite utilizar estas cookies, es posible que algunos de estos servicios no funcionen correctamente.

Cookies de publicidad: las cookies de marketing se utilizan para rastrear a los visitantes en las páginas web. La intención es mostrar anuncios relevantes y atractivos para el usuario individual, y, por lo tanto, más valiosos para los editores y terceros anunciantes.

Tratamiento de datos de carácter personal:

Alguna de estas cookies lleva consigo el tratamiento de datos de carácter personal. En el caso de que no quiera que recaben sus datos personales, podrá configurar las cookies pinchando aquí

Revocación y eliminación de Cookies:

En cualquier caso y en todo momento, podrás eliminar las cookies ya instaladas a través de la configuración del navegador. Dicha configuración la podrás llevar a cabo en:

Según el plazo de tiempo en que las cookies permanecen activadas en un equipo terminal, podemos distinguir dos tipologías:

Cookies de sesión: diseñadas para recabar y almacenar datos mientras el usuario accede a una página web. Se suelen emplear para almacenar información que solo interesa conservar para la prestación del servicio solicitado por el usuario en una sola ocasión.

Cookies persistentes: cookies en las que los datos permanecen almacenados en el terminal y pueden ser accedidos y tratados durante un periodo definido por el responsable de la cookie, y que puede variar desde unos minutos hasta varios años.

Actualización de la Política de Cookies:

AEE aconseja a los usuarios que visiten periódicamente este sitio web para conocer los cambios sufridos en las mismas, así como los cambios que se lleven a cabo en la presente Política de Cookies.